Home > Error Code > Copystar Error Code 2102

Copystar Error Code 2102

Contents

Then create a folder "scan" where you want ot receive the scanned files and add "scan" at the path field (SMB section of that webpage - command center).Now share the folder Main tray upper limit detection sensor or main tray load detection sensor is not detected as Off within 20 sec of main tray descending. The server is error status. Job is cancelled. weblink

Advanced Scanning Made Simple - Scanning is one of the most important functions of document workflow and should be easy to use and serve the purposes that your company needs. CF000 Operation Panel PWB Communication Error/System Error. Send error. replaced the developer units themselves. http://www.mytechtime.com/2008/10/kyocera-mita-common-error-codes.html

Kyocera Error Code 3101

E01001 or U01001 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Job is cancelled. Enter the disable host name/IP address. E01141 or U01141 Fax Communication Error: Reception in G3 mode was interrupted by a signal error.

No message reception after transmission of a CFR signal. F080 Flash ROM Error (during download). Reply With Quote 02-11-2009 #5 sprout Guest Thanks for the reply. Kyocera Error 2202 A DCN signal was received after transmission of an ERR signal (ECM).

A DCN signal was received after transmission of a DCS or NSS signal. C8210 DF-720 Finisher Stapler Problem. No message reception after transmission of an MCF signal. http://www.copytechnet.com/forums/kyocera-mita-copystar/17447-km-5050-smtp-set-up-error.html No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).

Reading or writing to the EEPROM cannot be performed. Kyocera Error Code 1102 Job is cancelled. During initial rotations home position is not detected within 1000ms. Sender address is not entered.

Kyocera Error Code 4803

Beyond that, I've used wireshark to track down some odd email problems on older Kyocera copiers, but I haven't seen the linux-based machines mess up email. https://stavola.wordpress.com/2011/03/30/kyocera-smb-error-2101/ If it doesn't connect, there's no usable SMTP server on that port. Kyocera Error Code 3101 E01051 or U01051 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Kyocera Printer Error Codes Required fields are marked * Name * Email * Website Comment You may use these HTML tags and attributes:

Tip: The max point reward for answering a question is 15. have a peek at these guys Send FTP Error 3101 Error: Server Response. Decrease the size or resolution of the scanned data to be transmitted and resend the E-mail. 5101, 5102, 5103, 5104, 7102, 720f: Turn the main power switch off and back on. Set server name to IP Address and turned auth off - same error though. Kyocera Send Error 2102

Expand Popular Questions 3 Answers ERROR CODE 2101 WHEN TRYING TO SCAN Kyocera Copystar CS-1820 Black... 2 Answers "match envelope switches" error message. E01000 or U01000 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Then click on Submit at the bottom of the page. (To add more contacts repeat steps 3 to 6.) Click on the Network link on the right. http://ogdomains.com/error-code/copystar-error-e33.php No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).

CFB2C CFB30 CFB31 Panel Error. Kyocera Send Error 2101 C1800 PF-700/PF-750 Communication Problem. C9070 DP-700 Communication Error between the DP and SHD.

Under Email fill in the email address of this Contact.

E01048 or U01048 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. E03600 or U03600 Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers. I have given smtp time out up to 90 seconds. Kyocera Error Code C6000 C6000 Fuser Heater Break.

Press [End]. Abnormal reading data from EEPROM. Send email Error 1102 Error: Username/Password. this content Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.

Press [End]. 1102 Send SMB Error: Username/Password or Shared Name/Folder Name. Software Error 5101 Error: Not Yet Connected. E01120 or U01120 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization.

Send error. C2600 PF-750 Paper Conveying Motor error. Increased office productivity is your top priority. F040 Engine PWB Communication Error.

C0130 Main PWB EEPROM Backup Memory Device Problem. E02200 or U02200 Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified. Add × Loading... Links Kyocera Link to Kyocera Downloads and Support click HERE.

EEPROM can not be written or read. Job is cancelled. Error for storage status in the operation handle. Settings are: SMTP = ONPort = 25SMTP Server = exchangeserverNameSMTP Timeout = 180 secondsAuthentication Protocol = ONAuthenticate As = OTHERUser name = USERNAME (that has been allowed in relay)Password = ++++++++Please

E01040 or U01040 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Error code J00 Help, we had a paper jam this morning, cleaned it out but now have ERROR CODE J00. Use Command center and turn on SMTP protocol setting.